Så efter lite Googlande insåg jag att det är inte så komplicerat att göra själv.
Jag börjar med en 25mm MDF ca 600x800mm
![DSC04426.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309227.jpg)
I denna MDF skall en 5mm aluminiumplåt fällas i.
Plåten fanns att få på lokala smidesverkstaden.
![DSC04427.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309298.jpg)
Jag borrade hål och försänkte skruvhålen .Centrumhålet körde ut jag med en hålsåg för trä,massor av 5-56/WD-40 för att smörja.Lämnade in plåten till vår lackverkstad så att den blev granner.
![DSC04428.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309423.jpg)
Nu e det snart dags att fräsa,men först märkt upp var jag vill ha plåten.
![DSC04429.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309470.jpg)
Fräsdags,utomhusgöra.
![DSC04430.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309511.jpg)
Färdigfräst, dags att såga ut biten i mitten.Kör med sticksåg då det inte behövs göras så snyggt.
![DSC04431.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309547.jpg)
Sågat å klart,nu ger det sig om plåten passar.
![DSC04432.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309587.jpg)
Tur eller? Den passa perfekt.Trot om ni vill men den ligger jäms med MDF.
![DSC04433.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309659.jpg)
Dags att montera fräsen, en vanlig Bosch överhandsfräs.Bort med bottenplattan,denna hade jag tdigare och malla för hålen när jag gjorde aluminiumplåten.
![DSC04435.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309713.jpg)
![DSC04438.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309747.jpg)
Ditskruvning av fräsen
![DSC04439.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309787.jpg)
Nu börjar det likna nåt.
![DSC04441.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309826.jpg)
Och så här ser det ut på undersidan
![DSC04442.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309862.jpg)
Nu ett fräsprov för att se om det blev som jag tänkt.Testar med en avrundningsfräs.
![DSC04443.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309911.jpg)
Nä men det funkar ju perfekt.Obs jag fräste på en skrotbit som inte var rakt sågad.
![DSC04444.jpg](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309956.jpg)
Och så här blir det med en bit som är lite bättre i kanten.
![DSC04445.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1258309994.jpg)
Nästa steg är att göra ett anhåll,en förhöjningsram på undersidan,ev spånutsug.
Något åt detta hållet,
![RouterTable__38.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1257608877.jpg)
![RouterTable__37.JPG](https://www.minhembio.com/forum/uploads/monthly_11_2009/post-3117-1257608977.jpg)
Redigerat av Hakon, 15 november 2009 - 19:34.